What is in this article?
- O-ring dimension and measurement image charts
- What are ID, OD and cross-section in an O-ring drawing?
- How to measure O-ring size without stretching it
- Metric O-ring measurements: 20 × 2, 12 × 2.5 and 30 × 3
- AS568 dash-number system and inch-series O-ring charts
- How to use the three O-ring reference diagrams
- O-ring material: NBR, EPDM, FKM and silicone are not equivalent
- Groove geometry, squeeze, stretch and extrusion risk
- Common measurement mistakes and a practical selection workflow
- How to calculate ring OD from ID and cross-section
- Frequently asked questions
- How do I calculate the outside diameter of an O-ring?
- Does a 20 × 2 mm O-ring have a 24 mm OD?
- What does AS568-214 mean?
- Is a metric O-ring always interchangeable with a similar AS568 size?
- Should I measure a stretched O-ring?
- Does the O-ring size specify chemical compatibility?
- Conclusion and specialist references
An O-ring is usually described by its free-state inside diameter (ID) and cross-section thickness (CS), not just by the outside diameter. For a simple round cross-section, OD ≈ ID + 2 × CS. For example, a nominal metric 20 × 2 mm ring has a 20 mm inside diameter, 2 mm section and approximately 24 mm outside diameter. AS568 inch-series rings use dash-number designations, while metric seals are commonly specified by dimensions in millimetres. These three diagrams show the dimensions, safe measurement method and standards terminology so you can identify an existing seal without confusing dimensions with material suitability.
Updated 21 November 2026. Examples illustrate geometry; check manufacturer specifications and material before use in any pressure or fluid system.
O-ring dimension and measurement image charts



What are ID, OD and cross-section in an O-ring drawing?
Inside diameter is the free inner opening of a relaxed O-ring; outside diameter is its outermost dimension; cross-section is the thickness of the round cord forming the ring. When a ring is ideal, undeformed and circular in section, the basic geometry is OD = ID + 2CS. This is a helpful memory rule, but actual manufactured seals have dimension tolerances, and used rings can become swollen, flattened or stretched.
The first figure labels all three dimensions clearly. When reading a supplier listing, check whether its description uses inside diameter × cross-section, outside diameter × section or a standard dash code. A bare notation like ’20 mm O-ring’ is incomplete because it may mean ID, OD or a nominal application size. The part’s fit and effectiveness also depend on the groove and the material. The formula does not decide whether a ring seals safely under pressure.
How to measure O-ring size without stretching it
Ideally measure a clean, unused ring at ordinary room conditions using a suitable calibrated measuring tool. Let the elastomer rest freely on a flat clean surface and avoid pulling it tight. Measure the ID without deforming the ring, then measure the cross-section at a few points with a tool appropriate for soft materials. Squeezing a soft O-ring with sharp caliper jaws can flatten the section and produce an artificially low reading.
Used rings may have permanent compression set, swelling from chemicals or cuts that make their dimensions unreliable. When possible, look up the original equipment part number or sealing-groove specification instead of reverse-engineering a severely worn ring. Record the measured ID, section and calculated OD with units and uncertainty. A photograph next to a ruler can help identify rough size, but it is generally not precise enough for critical replacement.
Metric O-ring measurements: 20 × 2, 12 × 2.5 and 30 × 3
Metric O-rings are frequently described by nominal inside diameter and section, for example 20 × 2 mm, 12 × 2.5 mm or 30 × 3 mm. Under the simple geometrical relation, those yield approximate outside diameters of 24 mm, 17 mm and 36 mm respectively. The notation is convenient for comparison, but a shop listing needs a clear statement about which dimension is first. Not every manufacturer structures an item title identically.
A ring with ID 20 mm and CS 2 mm cannot be treated as interchangeable with a ring that has OD 20 mm and CS 2 mm. They have different inside openings and fit different grooves. A seal may require a calculated amount of stretch and squeeze to function, so nominal close fit does not automatically mean appropriate replacement. Use the equipment manufacturer’s sealing detail or groove design specification when selecting an actual part.
AS568 dash-number system and inch-series O-ring charts
AS568 is a widely used inch-series O-ring dimensional standard. Instead of printing ID and CS as the only identifier, catalogues commonly show a three-digit dash-number family, such as -010, -214 or -325. The dash number maps to specific nominal dimensions and tolerances in the standard’s published table. It is not a self-contained formula that you should derive by reading the last digits as an inch dimension.
For example, a standard catalogue may identify a particular ring as AS568-214. Its size corresponds to the table entry for that exact dash number; the dash number alone does not tell you material, hardness, temperature rating or fluid compatibility. Confirm which revision or tolerance is required by your application, and be careful with look-alike metric sizes. Two rings may be close enough to be confused at a parts counter but outside the correct specified limits.
How to use the three O-ring reference diagrams
The first image labels ID and OD around the ring so you know which measurements correspond to the inner opening and the outside. The second diagram isolates cross-section, making it clear that cord thickness must not be omitted. The third gives a standards-focused visual layout and illustrates why dash numbers should be looked up rather than guessed. Use the images to create a measurement note, not as a substitute for a dimensioned manufacturer drawing.
For a spare-parts bag, write the nominal ID, cross-section, units, original equipment number and material if known. Add the intended sealing location, such as a faucet valve, pump cover or hydraulic port. If only the damaged seal remains, record whether it appears cut, cracked, swollen or flattened. Such notes can help the technician determine whether the correct size failed due to wear, chemistry or operating conditions rather than being mis-sized from the start.
O-ring material: NBR, EPDM, FKM and silicone are not equivalent
The same physical size can be manufactured in different elastomers. NBR is common for certain oil- and fuel-related uses, EPDM can be appropriate for selected water and weather environments, FKM is selected for some chemical and temperature demands, and silicone is used where certain thermal or flexibility properties matter. However these are broad categories; each compound grade has its own compatibility and rating.
Never assume that matching dimensions makes a seal suitable for drinking water, food, oxygen, gas, fuel, hydraulic fluids or medical applications. Fluid chemistry, temperature, pressure, regulatory approval and material hardness all matter. An application-compatible material can also require a certain compression set or aging performance. Consult the supplier’s compound data and the equipment manufacturer’s approved replacement specification.
Groove geometry, squeeze, stretch and extrusion risk
An O-ring seals by being compressed within a designed groove, also called a gland. The ring must experience the intended squeeze while leaving appropriate room for swelling, movement and tolerances. Excessive squeeze can damage the material; insufficient squeeze can cause leakage. Under high pressure, unsupported elastomer can extrude into a clearance gap. Some designs use back-up rings to control that risk.
The correct fit depends on whether the seal is static or dynamic, whether it is radial or axial, direction of pressure, hardware tolerances, motion and lubrication. A simple ring-dimension chart cannot specify the correct groove design or allowable pressure. In hydraulic or pneumatic machinery, the manufacturer’s seal design handbook or a qualified engineer should confirm dimensions, compound and installation details. Do not rely on random generic percentages for every possible groove.
Common measurement mistakes and a practical selection workflow
An easy mistake is measuring the old ring while it is stretched around a part, then treating the measured ID as its nominal free state. Another is measuring the compressed section on a seal with visible flats. A third is choosing an AS568 ring by outside diameter alone without checking its section. Finally, converting inch dimensions into rounded metric numbers can create a near match that is outside tolerance.
The safer sequence is to identify the equipment and service medium, obtain the designed ring size or catalogue number, confirm free-state ID and CS, check standard and tolerances, then match material and application ratings. Use clean installation practices, protect the ring from sharp edges and avoid twists, cuts or unsuitable lubricant. Before reopening a pressure system, complete manufacturer-required inspection and testing. The geometric chart is a useful first step, not the whole sealing decision.
How to calculate ring OD from ID and cross-section
| Nominal ID | Cross-section CS | Approximate OD |
|---|---|---|
| 10 mm | 1.5 mm | 13 mm |
| 12 mm | 2.5 mm | 17 mm |
| 20 mm | 2 mm | 24 mm |
| 25 mm | 2.5 mm | 30 mm |
| 30 mm | 3 mm | 36 mm |
| 40 mm | 3.5 mm | 47 mm |
Nominal geometry examples only, not verified catalogue listings or tolerance-compliant replacement recommendations.
Frequently asked questions
How do I calculate the outside diameter of an O-ring?
For a round section in the relaxed ideal case, OD ≈ ID + 2 × cross-section.
Does a 20 × 2 mm O-ring have a 24 mm OD?
Approximately, under the nominal ID × CS convention and excluding manufacturing tolerance.
What does AS568-214 mean?
A standardized inch-series dash-number O-ring size; look up its exact dimensions in an AS568 chart.
Is a metric O-ring always interchangeable with a similar AS568 size?
No. Match dimensional tolerance, groove design and material requirements.
Should I measure a stretched O-ring?
No. Free-state dimensions are the intended starting point.
Does the O-ring size specify chemical compatibility?
No. Material compound and approvals are separate specifications.
Conclusion and specialist references
Always identify both nominal size and elastomer material, then check the sealing application. If the old O-ring is damaged, a design drawing is more reliable than trying to guess its original dimensions.

Share Your Opinion
Comments are closed on this post.